MILFORD, CT —
OSHA Inspection: ALINABAL, LLC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ALINABAL, LLC in 28 WOODMONT ROAD, MILFORD, CT 06460 (NAICS 332999). OSHA activity number 347629388.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Alinabal, LLC — free
Get an email when a new federal OSHA severe-injury report for Alinabal, LLC is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- ALINABAL, LLC
- Site address
- 28 WOODMONT ROAD
- City
- MILFORD
- State
- CT
- ZIP
- 06460
- Mailing
- 28 WOODMONT ROAD, MILFORD, CT 06460
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332999
- Employees
- 260
- Ownership type
- A
Citations
11 citations on file for this inspection.
1910.37 B04
- Issued
- Sep 20, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.37(b)(4): When the direction of travel to the exit or exit discharge was not immediately apparent, signs were not posted along the exit access indicating the direction of travel to the nearest exit and exit discharge: Location - Multiple areas through the establishment: On 07-11-24, the direction of travel to the nearest exit was not apparent in the following exit access areas: a) Along main aisle in 424 area b) Aisle in Punch Press area c) Aisle to Maintenance shop d) Aisle at Deburring area e) Along main aisle in 430 stock area
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C04 I
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $9,795 · Current $9,795
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section. a) Location - Press room area: Die maintenance on Press #139: On or about 05-10-24, a LOTO procedure was not utilized while unbolting and freeing the punch holder from the die. and the unexpected gravitational energy caused an unstable part of an upper die to fall and cause an injury to the employee's finger. b) Location - Short Run area: Die set-up on Press #424-49: On 07-11-24, LOTO procedures were not being utilized for die changing or die set-up tasks for punch presses. c) Location - Short Run area: Die set-up on Press #TN1-45: On 07-11-24, a LOTO procedure was not developed or utilized for die set-up tasks for a new power press.
Recent events (2)
- — I (S) $9795
- — Z (S) $9795
1910.217 D09 I
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(d)(9)(i): The employer did not establish a die setting procedure for mechanical power press(es) that would ensure compliance with 29 CFR 1910.217(c). Location - Establishment: On or about 07-11-24, the written die setting procedure did not instruct employees to lock out-tag out power presses prior to and during die set-up installations, adjustments, removal of punch holders, and die removal activities as per 1910.147.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C04 II B
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $9,795 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(B): The energy control procedures did not clearly and specifically outline the steps for shutting down, isolating, blocking and securing machines or equipment to control hazardous energy. Location - Establishment's written LOTO program: a) On 05-10-24, LOTO procedures do not instruct authorized persons how to control the gravitational energy that could cause struck-by or crushing injuries to hands or fingers while removing and re-installing punch holders in the upper die of presses.
Recent events (2)
- — I (S) $0
- — Z (S) $9795
1910.147 C04 II C
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(C): The energy control procedure did not clearly and specifically outline the steps for placement, removal and transfer of lockout devices or tagout devices and the responsibility for them. Location - Establishment's written LOTO program: On or about 07-11-24, written LOTO procedures for equipment with pneumatic air lines as an additional source of energy do not clearly describe how to place a lockout device or tag on a valve or disconnect to ensure the hazardous energy isolating means is either locked and tagged, or tagged out to control the energy source.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C07 I A
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $9,795 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Authorized employee(s) did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation. Location - Establishment: On or about 07-11-24, die setters, tool makers and press operators who perform set-up of power presses are not trained in LOTO as authorized employees.
Recent events (2)
- — I (S) $0
- — Z (S) $9795
1910.147 C07 I B
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i)(B): Affected employees were not instructed in the purpose and use of the energy control procedure: Location - Establishment: On or about 07-11-24, each affected employee had not received training in the purpose and use of LOTO procedures applicable to the equipment they are tasked to operate.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A03 II
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $9,795 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): Location: Deburring area On 07/11/24, the barrier guard for the Timesaver Head Sander had gaps on each side , which could permit the operator to reach into the in-going nip point of the head roller.
Recent events (2)
- — I (S) $0
- — Z (S) $9795
1910.1200 F08
- Issued
- Sep 20, 2024
- Penalty
- Initial $9,795 · Current $0 Reduced
General-duty citation text
29 CFR 1910.1200(f)(8): The employer did not ensure that portable containers into which hazardous chemicals were transferred from labeled containers and which were not intended for the immediate use of the person doing the transfer, were properly labeled. Location - manual deburring area: On 07-11-24, a portable spray bottle containing MEK did not have a label on the bottle.
Recent events (2)
- — I (O) $0
- — Z (S) $9795
1910.1200 H01
- Issued
- Sep 20, 2024
- Abate by
- Oct 17, 2024
- Penalty
- Initial $9,795 · Current $0 Reduced
General-duty citation text
29 CFR 1910.1200(h)(1): Employees were not provided effective information and training on hazardous chemicals in their work area at the time of their initial assignment and whenever a new hazard that the employees had not been previously trained about was introduced into their work area: Location - Establishment: On or about 07-11-24, the employer did not train employees who work in the manual deburring area of the chemical hazards they work with, such as MEK when spraying on parts within the deburring process.
Recent events (2)
- — I (O) $0
- — Z (S) $9795
1910.37 B02
- Issued
- Sep 20, 2024
- Penalty
- Initial $9,795 · Current $9,795
General-duty citation text
29 CFR 1910.37(b)(2): Each exit was not clearly visible and marked by a sign reading "Exit": Location - Maintenance shop: On 07-11-24, the exit door to outside from the maintenance shop not marked with a sign.
Recent events (2)
- — I (O) $9795
- — Z (S) $9795
More inspections at Alinabal, LLC
View Alinabal, LLC's full OSHA safety record →
More inspections in this industry (NAICS 332999)
Jul 16, 2026
Metal Vision INC. · SMITHFIELD, UT
Jul 15, 2026
111597 - Chandler Industries INC - Blaine Division · MINNEAPOLIS, MN
Jul 13, 2026
A09cs000012fnxzaaq - Dubuque Steel Products · DUBUQUE, IA
Jul 10, 2026
Dorstener Wire Tech INC. · SPRING, TX
Jul 10, 2026
ED Long'S Metal Works · SAN ANTONIO, TX
More inspections in CT
Jul 16, 2026
Bianco & Sons, LLC · EAST HAVEN, CT
Jul 16, 2026
Moms Enfield · ENFIELD, CT
Jul 16, 2026
Harbor Freight · DAYVILLE, CT
Jul 14, 2026
Jananii, LLC · NEW BRITAIN, CT
Jul 14, 2026
Truss Manufacturing INC · NEWINGTON, CT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347629388.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.