STAFFORD, TX —
OSHA Inspection: D&R SIGNS, LLC
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of D&R SIGNS, LLC in 12999 MURPHY ROAD, STAFFORD, TX 77477 (NAICS 339950). OSHA activity number 347759276.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- D&R SIGNS, LLC
- Site address
- 12999 MURPHY ROAD
- City
- STAFFORD
- State
- TX
- ZIP
- 77477
- Mailing
- ATTN: CORY KAMEGO 4801 W UNIVERSITY DR #102, DENTON, TX 76207
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 339950
- Employees
- 44
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.253 B02 II
- Issued
- Dec 19, 2024
- Penalty
- Initial $5,288 · Current $2,644 Reduced
General-duty citation text
29 CFR 1910.253(b)(2)(ii): Assigned storage spaces for cylinders were located where cylinders could be knocked over or damaged by passing or falling objects, or subject to tampering by unauthorized persons: a) On or about September 17, 2024, in the middle of the shop, where employees were working in areas adjacent to compressed gas cylinders that were not secured.
Recent events (2)
- — I (S) $2644
- — Z (S) $5288
1910.213 C01
- Issued
- Dec 19, 2024
- Penalty
- Initial $14,518 · Current $7,259 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: a) On or about September 17, 2024, in the shop, where employees cut materials using a Delta table saw that was not equipped with a guard.
Recent events (2)
- — I (S) $7259
- — Z (S) $14518
1910.213 C02
- Issued
- Dec 19, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator: a) On or about September 17, 2024, in the shop, where employees cut materials using a Delta table saw that was not equipped with a spreader.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 C03
- Issued
- Dec 19, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: a) On or about September 17, 2024, in the shop, where employees cut materials using a Delta table saw that was not equipped with anti-kickback fingers.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.252 B02 III
- Issued
- Dec 19, 2024
- Abate by
- Jan 2, 2025
- Penalty
- Initial $8,816 · Current $4,408 Reduced
General-duty citation text
29 CFR 1910.252(b)(2)(iii): Workers and other persons adjacent to the welding area were not required to wear appropriate goggles, to protect them from the rays when noncombustible or flameproof screens or shields were not used: (a) On or about September 17, 2024, in the shop, where employees working adjacent to welding operations were not protected from welding rays.
Recent events (2)
- — I (S) $4408
- — Z (S) $8816
1910.305 G02 III
- Issued
- Dec 19, 2024
- Penalty
- Initial $990 · Current $495 Reduced
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords were not connected to devices and fittings so that tension would not be transmitted to joints or terminal screws: a) On or about September 17, 2024, in the shop, where an extension cord connected to the Delta table saw did not have strain relief and the cover was pulled away, exposing the insulated wires.
Recent events (2)
- — I (O) $495
- — Z (O) $990
1910.37 A03
- Issued
- Dec 19, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.37(a)(3): Exit route(s) were not kept free and unobstructed: a) On or about September 17, 2024, in the shop, where an exit route was obstructed by items such as, but not limited to, a floor jack and hoses.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at D&R Signs, LLC
View D&R Signs, LLC's full OSHA safety record →
More inspections in this industry (NAICS 339950)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347759276.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.