ADAIRSVILLE, GA —
OSHA Inspection: SINERGY ELASTOMERS INC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of SINERGY ELASTOMERS INC in 400 NORTH MAIN STREET NORTHWEST, ADAIRSVILLE, GA 30103 (NAICS 325110). OSHA activity number 347942450.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SINERGY ELASTOMERS INC
- Site address
- 400 NORTH MAIN STREET NORTHWEST
- City
- ADAIRSVILLE
- State
- GA
- ZIP
- 30103
- Mailing
- 400 NORTH MAIN STREET NORTHWEST, ADAIRSVILLE, GA 30103
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 325110
- Employees
- 14
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 C01
- Issued
- Mar 3, 2025
- Abate by
- Mar 31, 2025
- Penalty
- Initial $6,620 · Current $6,620
General-duty citation text
29 CFR 1910.147(c)(1):The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: (a) Production floor; On or about, December 18, 2024, and time prior, the employer exposed employees to caught-in hazards, in that the employer did not establish an effective program for control of hazardous energy for authorized and affected employees who are exposed to LOTO requirements.
Recent events (2)
- — I (S) $6620
- — Z (S) $6620
1910.147 C04 I
- Issued
- Mar 3, 2025
- Abate by
- Mar 31, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(i):Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: (a) Mixtruder, 100 mixer, 200 mixer, 400 mixer - Production floor; On or about, December 18, 2024, and time prior, the employer exposed employees to caught-in hazards, in that the employer did not did not develop LOTO that would control the potential of hazardous energy release when employees are engaged in maintenance/servicing activities. (b) Roll Mill - Lab, On or about, December 18, 2024, and time prior, the employer exposed employees to caught-in hazards, in that the employer did not establish an effective program for control of hazardous energy for authorized and affected employees who are exposed to LOTO requirements
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.178 L01 II
- Issued
- Mar 3, 2025
- Abate by
- Mar 31, 2025
- Penalty
- Initial $6,620 · Current $4,380 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(ii):The employer did not ensure that each operator had successfully completed the training required by paragraph (l), except as permitted by paragraph (l)(5), prior to permitting an employee to operate a powered industrial truck (a) Production floor; On or about, December 18, 2024, and time prior, the employer exposed employees to struck-by hazards in that the required training contents of a Powered Industrial Truck Program was not provided to employees who operate the powered industrial trucks 2 LP forklifts (1 walk behind, 1 - 10K Reach truck), on the Production floor.
Recent events (2)
- — I (O) $4380
- — Z (S) $6620
1910.212 A02
- Issued
- Mar 3, 2025
- Abate by
- Mar 31, 2025
- Penalty
- Initial $4,729 · Current $2,000 Reduced
General-duty citation text
29 CFR 1910.212(a)(2): Guard(s) on machine(s) were not affixed to the machine or secured elsewhere when attachment to the machine was not possible: (a) Mixtruder - Production floor; On or about, December 18, 2024, and time prior, the employer exposed employees to caught-in hazards, in that machine guarding for the mixtruder was ineffective where screws on the guarding were missing, exposing employees to caught-in/rotating parts while employees operate the mixtruder.
Recent events (2)
- — I (O) $2000
- — Z (S) $4729
1910.303 B07
- Issued
- Mar 3, 2025
- Abate by
- Mar 31, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.303(b)(7): Electrical equipment was not installed in a neat and workmanlike manner: (a) Production floor; On or about, December 18, 2024, and time prior, the employer exposed employees to electrical shock hazards in that electrical conductors and conduit were not installed in a neat and workmanlike manner exposing the insulated wires and the weight of the conduit which was not secured to the equipment surface where elevated above the floor, was supported by the enclosed conductors.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections in this industry (NAICS 325110)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347942450.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.