HIGH POINT, NC —
OSHA Inspection: STILES MACHINERY, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of STILES MACHINERY, INC. in 729 GALLIMORE DAIRY ROAD, HIGH POINT, NC 27265 (NAICS 423830). OSHA activity number 309512382.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- STILES MACHINERY, INC.
- Site address
- 729 GALLIMORE DAIRY ROAD
- City
- HIGH POINT
- State
- NC
- ZIP
- 27265
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 423830
- SIC code (legacy)
- 5084
- Employees
- 40
- Ownership type
- A
- Industry flags
- Manufacturing health.
Citations
14 citations on file for this inspection.
95012901
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
- Penalty
- Initial $1,225 · Current $800 Reduced
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a)Being crushed by a forklift in the event of a roll over, due to the lack of an employee wearing the seatbelt. Adjacent to shipping/receiving area, an employee was observed not wearing the seatbelt when operating the Clark forklift. If a rollover occurred, an employee could try to leave the forklift or be tossed from the operator's seat, and be crushed by the forklift. Reference: ASME B56.1-1993, revision of ASME/ANSI B56.1-1988, paragraph 5.3.19 - An active operator protection device or system, when provided, shall be used. Operator protection in the event of tip over is intended to reduce the risk of entrapment of the head and torso between the truck and the ground. NOTE: Among other methods, one feasible and acceptable abatement method to correct this hazard is to require and ensure that employees use the seatbelts on the forklifts.
Recent events (2)
- — I (S) $800.00
- — Z (S) $1225.00
1910.178 L04 IIA
- Issued
- Feb 21, 2006
- Abate by
- Mar 17, 2006
Recent events (2)
- — I (O)
- — Z (S)
1910.22 D01
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.124 G02
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.132 D01
- Issued
- Feb 21, 2006
- Abate by
- Apr 7, 2006
1910.132 F01
- Issued
- Feb 21, 2006
- Abate by
- Mar 17, 2006
1910.133 A01
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.303 B02
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.1200 E01
- Issued
- Feb 21, 2006
- Abate by
- Apr 7, 2006
1910.1200 E01 I
- Issued
- Feb 21, 2006
- Abate by
- Apr 7, 2006
1910.1200 F05 I
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.1200 F05 II
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.1200 G01
- Issued
- Feb 21, 2006
- Abate by
- Feb 24, 2006
1910.1200 H01
- Issued
- Feb 21, 2006
- Abate by
- Mar 17, 2006
More inspections at Stiles Machinery, INC.
View Stiles Machinery, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 423830)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 309512382.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.