CUDAHY, WI —
OSHA Inspection: LIPPMANN-MILWAUKEE, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of LIPPMANN-MILWAUKEE, INC. in 3271 EAST VAN NORMAN AVENUE, CUDAHY, WI 53110 (NAICS 333120). OSHA activity number 311397376.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Lippmann-Milwaukee, INC. — free
Get an email when a new federal OSHA severe-injury report for Lippmann-Milwaukee, INC. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- LIPPMANN-MILWAUKEE, INC.
- Site address
- 3271 EAST VAN NORMAN AVENUE
- City
- CUDAHY
- State
- WI
- ZIP
- 53110
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333120
- SIC code (legacy)
- 3531
- Employees
- 67
- Ownership type
- A
Citations
14 citations on file for this inspection.
5(a)(1)
- Issued
- Jun 19, 2008
- Abate by
- Jul 7, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the point of operation: The foot treadle, on the 65 Ton Verson Press Brake #97, was not guarded to prevent accidental actuation. Among other methods, feasible and acceptable means to correct these hazards are: (1)Implement the requirements outlined in American National Standards Institute ANSI B11.3-2002 for Machine Tools - Safety Requirements for Power Press Brakes, Section 6.10.3 Unattended actuation of press brake by foot treadle. When provided, a foot treadle of the type that services as an operator control shall be equipped with a means to prevent unattended machine actuation. (2)Provide a protective cover over the treadle bar to prevent unattended machine actuation. (3)Provide a locking pin or locking lever to lock the treadle bar in a fixed position. These locking mechanisms should be designed to prevent unattended machine actuation. The locking mechanism should not allow locking in the operating position. Certification, and documentation/evidence of abatement is required. Certification of abatement is required by 29 CFR Part 1903 and is to be submitted within ten (10) calendar days after the abatement date.ment
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
5(a)(1)
- Issued
- Jun 19, 2008
- Abate by
- Jul 7, 2008
- Penalty
- Initial $1,500 · Current $600 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees are exposed to struck by and crushing hazards: (a)Bay 3, a spreader beam, used as a below-the-hook device is set-up with two 35 Ton Overhead Cranes did not have the rated load marked or identification on the manufacturer and serial number exposing employees to crushing or struck by injuries. Among other methods, feasible and acceptable means to correct these hazards are to use a safer alternate method such as: 1.Implement the requirements as defined in ASME B30.20a-2001, Section 20-1.2.1 (a): Rated Load. The rated load of the lifting device shall be marked on the main structure where it is visible. If the lifting device is made up of several lifters, each detachable from the group, these lifters shall also be marked with their individual rated loads, and Section 20-1.2.1 (b) Identification. A nameplate or other permanent marking shall be affixed displaying the following information: (1) manufacturer's name and address; (2) serial number; (3) lifter weight, if over 100 lbs (45 kg); (4) rated load. Certification, with date and method of abatement required. Certification of abatement is required by 29 CFR Part 1903 and is to be submitted within ten (10) calendar days after the abatement date.ment
Recent events (2)
- — I (S) $600.00
- — Z (S) $1500.00
1910.147 C06 I
- Issued
- Jun 19, 2008
- Abate by
- Jul 22, 2008
- Penalty
- Initial $1,500 · Current $600 Reduced
Recent events (2)
- — I (S) $600.00
- — Z (S) $1500.00
1910.178 L01 II
- Issued
- Jun 19, 2008
- Abate by
- Aug 8, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 B05
- Issued
- Jun 19, 2008
- Abate by
- Jun 24, 2008
- Penalty
- Initial $1,500 · Current $600 Reduced
Recent events (2)
- — I (S) $600.00
- — Z (S) $1500.00
1910.179 J02
- Issued
- Jun 19, 2008
- Abate by
- Jul 7, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 J02 III
- Issued
- Jun 19, 2008
- Abate by
- Jun 24, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 N02 I
- Issued
- Jun 19, 2008
- Abate by
- Jun 24, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 N03 IV
- Issued
- Jun 19, 2008
- Abate by
- Jul 7, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 N03 IX
- Issued
- Jun 19, 2008
- Abate by
- Aug 8, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (2)
- — I (S) $1200.00
- — Z (S) $3000.00
1910.212 A01
- Issued
- Jun 19, 2008
- Abate by
- Jul 7, 2008
- Penalty
- Initial $1,500 · Current $600 Reduced
Recent events (2)
- — I (S) $600.00
- — Z (S) $1500.00
1910.212 A03 II
- Issued
- Jun 19, 2008
- Abate by
- Dec 31, 2008
- Penalty
- Initial $3,000 · Current $1,200 Reduced
Recent events (3)
- — P (S) $1200.00
- — I (S) $1200.00
- — Z (S) $3000.00
1910.179 N01
- Issued
- Jun 19, 2008
- Abate by
- Jul 1, 2008
- Penalty
- Initial $56,000 · Current $22,400 Reduced
Recent events (2)
- — I (W) $22400.00
- — Z (W) $56000.00
1910.179 G01 IV
- Issued
- Jun 19, 2008
- Abate by
- Jul 1, 2008
- Penalty
- Initial $2,400 · Current $600 Reduced
Recent events (2)
- — I (R) $600.00
- — Z (R) $2400.00
More inspections at Lippmann-Milwaukee, INC.
Jan 11, 2013
CUDAHY, WI
May 2, 2012
CUDAHY, WI
Jan 31, 2008
CUDAHY, WI
May 17, 2007
CUDAHY, WI
Sep 3, 2003
CUDAHY, WI
View Lippmann-Milwaukee, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333120)
Jul 9, 2026
JP Skidmore LLC · MENOMINEE, MI
Jul 8, 2026
111549 - Schwing America INC · SAINT PAUL, MN
Jul 7, 2026
69280 - Kemper Construction LLC · CARROLLTON, KY
Jun 16, 2026
111422 - Jenkins Iron and Steel INC · LONG PRAIRIE, MN
Jun 11, 2026
Timberpro, INC. · SHAWANO, WI
More inspections in WI
Jul 17, 2026
PTS Contractors, INC. · GREEN BAY, WI
Jul 16, 2026
Miron Construction CO. INC. · WAUSAU, WI
Jul 15, 2026
Wabash National Services, L.P. · ELROY, WI
Jul 15, 2026
Kings Superior Construction LLC · SUSSEX, WI
Jul 15, 2026
Teronomy Builders, INC. · DELAVAN, WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 311397376.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.