SAN ANTONIO, TX —
OSHA Inspection: TAKUMI STAMPING TEXAS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of TAKUMI STAMPING TEXAS, INC. in 1 LONE STAR PASS, BLDG.40, SAN ANTONIO, TX 78264 (NAICS 332116). OSHA activity number 340596113.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TAKUMI STAMPING TEXAS, INC.
- Site address
- 1 LONE STAR PASS, BLDG.40
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78264
- Mailing
- 1 LONE STAR PASS, BLDG.40, SAN ANTONIO, TX 78264
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332116
- Employees
- 180
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.184 F05 III
- Issued
- Aug 14, 2015
- Abate by
- Aug 24, 2015
- Penalty
- Initial $2,700 · Current $1,620 Reduced
General-duty citation text
29 CFR 1910.184(f)(5)(iii): Wire rope sling(s) that had kinking, crushing, bird caging or other damage resulting in distortion of the wire rope structure were not immediately removed from service: Material Receiving Dock: On or about April 22, 2015, employees were exposed to struck by hazards, while employees were rigging coil of flat steel with a Permaloc 6 foot wire rope sling (SN: 356440-24) that was kinked with minimal bird caging.
Recent events (2)
- — I (S) $1620
- — Z (S) $2700
1910.212 A01
- Issued
- Aug 14, 2015
- Penalty
- Initial $3,600 · Current $2,160 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: PR11 Stamping Machine: On or about April 22, 2015, an employee was exposed to the hazard of being caught by moving parts, while operating a stamping machine that had the Straightener/Leveler section of the machine's access door open where adjustments were made.
Recent events (2)
- — I (S) $2160
- — Z (S) $3600
1910.242 B
- Issued
- Aug 14, 2015
- Abate by
- Aug 24, 2015
- Penalty
- Initial $3,600 · Current $2,160 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning purposes was not reduced to less than 30 p.s.i.: a) Maintenance shop: On or about April 22, 2015, employees were exposed to the hazard of being struck by flying projectiles when operating the blow off gun of a Chung Milling Machine (SN: 3160) while cleaning the machine and parts without a safety relief device at pressures over 30 p.s.i. b) Maintenance shop: On or about April 22, 2015, employees were exposed to the hazard of being struck by flying projectiles when operating the blow off gun of a Chin Hung Lathe (Model CH-400) while cleaning the machine and parts without a safety relief device at pressures over 30 p.s.i.
Recent events (2)
- — I (S) $2160
- — Z (S) $3600
More inspections at Takumi Stamping Texas, INC.
View Takumi Stamping Texas, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332116)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340596113.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.