COLORADO SPRINGS, CO —
OSHA Inspection: COLORADO ARCHITECTURAL MILLWORK SUPPLY, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of COLORADO ARCHITECTURAL MILLWORK SUPPLY, INC. in 163 TALAMINE COURT, COLORADO SPRINGS, CO 80907 (NAICS 337212). OSHA activity number 342883808.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- COLORADO ARCHITECTURAL MILLWORK SUPPLY, INC.
- Site address
- 163 TALAMINE COURT
- City
- COLORADO SPRINGS
- State
- CO
- ZIP
- 80907
- Mailing
- 163 TALEMINE COURT, COLORADO SPRINGS, CO 80907
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337212
- Employees
- 23
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 C04 I
- Issued
- Feb 20, 2018
- Abate by
- Mar 23, 2018
- Penalty
- Initial $2,956 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure lockout/tagout procedures were utilized at all times when employees were required to engage in machine maintenance activities, where the release of hazardous energy could cause severe injury.
Recent events (2)
- — I (S) $1500
- — Z (S) $2956
1910.213 C02
- Issued
- Feb 20, 2018
- Abate by
- Mar 9, 2018
- Penalty
- Initial $2,217 · Current $1,500 Reduced
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator: a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure employees were protected from stuck-by hazards while operating and working in the vicinity of a Tannewitz (table saw) without a spreader device.
Recent events (2)
- — I (S) $1500
- — Z (S) $2217
1910.213 C03
- Issued
- Feb 20, 2018
- Abate by
- Mar 9, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure employees were protected from kickback hazards while operating and working in the vicinity of a Tannewitz table saw which was not equipped with non-kickback fingers. a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure employees were protected from kickback hazards while operating and working in the vicinity of a Altendorf F45 table saw which was not equipped with non-kickback fingers.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- Feb 20, 2018
- Abate by
- Mar 9, 2018
- Penalty
- Initial $2,217 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc., did not ensure employees, who were required to operate a Grizzly G0622 horizontal band saw, were protected from amputation hazards, in that the unused portion of the blade was not guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $2217
1910.213 J03
- Issued
- Feb 20, 2018
- Abate by
- Mar 9, 2018
- Penalty
- Initial $2,956 · Current $0 Reduced
General-duty citation text
29 CFR 1910.213(j)(3): The guard did not effectively keep the operator's hand from coming in contact with the revolving knives a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure that the fence guard on the Faye-Eagan Jointer was adjusted to cover the unused portion of the head, so as to protect employees from amputation hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $2956
1910.213 S09
- Issued
- Feb 20, 2018
- Abate by
- Mar 9, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(s)(9): Suitable sizes and types of push sticks or push blocks were not provided at the work place: a) On or about January 17, 2018, the employer, Colorado Architectural Millwork Supply, Inc. did not ensure push sticks or blocks were provided to use with the Faye-Eagan Jointer, so as to protect employees from amputation hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Colorado Architectural Millwork Supply, INC.
View Colorado Architectural Millwork Supply, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 337212)
More inspections in CO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342883808.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.