OSHA Inspection: MARTIN CABINET, INC.

Issued

May 9, 2018

Abate by

Jun 26, 2018

Penalty

Initial $5,174 · Current $3,622 Reduced

General-duty citation text

29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms, service rooms, and walking-working surfaces were not kept in a clean, orderly, and sanitary condition:  On, or about, March 14, 2018, in the following locations, combustible wood dust had accumulated on a wall ledges, electrical boxes and equipment:  A.  Side Cutting Room, Radial Arm Saw work station. B.  Assembly, Orange UniPoint radial arm saw.

Issued

May 9, 2018

Abate by

Jun 26, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.22(a)(2): The floor of each workroom was not maintained in a clean and, to the extent feasible, in a dry condition:  On, or about, March 14, 2018, in the following locations, combustible wood dust had accumulation on the floors:    A.  Side Cutting Room, radial arm saw work station. B.  Cabinet Assembly Area.

Issued

May 9, 2018

Abate by

Jun 26, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(s)(6): Emphasis was not placed upon the importance of maintaining cleanliness around woodworking machinery, particularly as regards the effective functioning of guards and the prevention of fire hazards in switch enclosures, bearings, and motors:  Side Cutting Room:  On, or about March 14, 2018, combustible wood dust had accumulated inside of the Square D motor starter box provided for the UniPoint radial arm saw.

Issued

May 9, 2018

Abate by

Jun 26, 2018

Penalty

Initial $5,174 · Current $3,622 Reduced

General-duty citation text

29 CFR 1910.133(a)(3): The employer did not ensure that employees wearing prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design or wears eye protection that can be worn over the prescription lenses:   Shop:  On, or about, March 14, 2018, employees who required prescription glasses or reading glasses were observed operating wood-working equipment without proper safety glasses.

Issued

May 9, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1904.41(a)(2): 29 CFR 1904.41(a)(2) Annual electronic submission of OSHA Form 300A Summary of Work-Related Injuries and Illnesses by establishments with 20 or more employees but fewer than 250 employees in designated industries. If your establishment had 20 or more employees but fewer than 250 employees at any time during the previous calendar year, and your establishment is classified in an industry listed in appendix A to subpart E of this part, then you must electronically submit information from OSHA Form 300A Summary of Work-Related Injuries and Illnesses to OSHA or OSHA's designee. You must submit the information once a year, no later than the date listed in paragraph (c) of this section of the year after the calendar year covered by the form.  Located at the Martin Cabinet, Inc., 500 Broad Street, Bristol, Connecticut:  On or about March 14, 2018, the employer failed during calendar year 2017, to electronically submit information from their OSHA Form 300A or equivalent by 12/31/2017  a). The establishment employed 48 employees and was classified as NAICS 337110 during calendar year 2016.  The employer did not enter the 2016 OSHA 300A data by the December 31, 2017 deadline.

Issued

May 9, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(h)(4): Radial saw(s) were not installed in a manner so as to cause the cutting head to return gently to the starting position when released by the operator:  On, or about, March 14, 2018, in the following locations, the automatic return mechanism provided on the following radial arm saws was not working properly:    A.  Side Cutting Room:  Rockwell radial arm saw. B.  Assembly Area:  UniPoint radial arm saw.