COLUMBUS, OH —
OSHA Inspection: INTERNATIONAL TECHNICAL COATINGS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of INTERNATIONAL TECHNICAL COATINGS, INC. in 845 EAST MARKISON AVE, COLUMBUS, OH 43207 (NAICS 332618). OSHA activity number 343468674.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- INTERNATIONAL TECHNICAL COATINGS, INC.
- Site address
- 845 EAST MARKISON AVE
- City
- COLUMBUS
- State
- OH
- ZIP
- 43207
- Mailing
- 845 EAST MARKISON AVE, COLUMBUS, OH 43207
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332618
- Employees
- 100
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.147 C04 I
- Issued
- Jan 28, 2019
- Abate by
- Feb 15, 2019
- Penalty
- Initial $12,934 · Current $12,934
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section. a. On or about September 13, 2018, the employer did not ensure that the developed and documented energy control procedures were being utilized by employees performing set up activities on the Ideal FSD 074 Fenceline resistance welder. Covered activities included, but were not limited to, wire change overs.
Recent events (1)
- — Z (S) $12934
1910.147 C07 I A
- Issued
- Jan 28, 2019
- Abate by
- Feb 15, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control. a. On or about September 13, 2018, the employer failed to ensure that each employee performing set up activities on the Ideal FSD 074 Fenceline resistance welder was effectively trained to understand the purpose and function of the energy control procedures, to recognize hazardous energy sources involved, and had the knowledge and skills required to lockout the equipment.
Recent events (1)
- — Z (S) $0
1910.147 D
- Issued
- Jan 28, 2019
- Abate by
- Feb 15, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence as required by 29 CFR 1910.147(d)(1) through (d)(6): a. On or about September 13, 2018, the employer did not ensure that employees implemented energy control procedures prior to performing set up activities on the Ideal FSD 074 Fenceline resistance welder. Covered activities included, but were not limited to, wire change overs. An unexpected movement of the welder's line wire magazine exposed an employee to a caught in hazard. Energy control procedures, such as isolation of energy sources from the machine [1910.147(d)(3)], the application of a lock-out device to control each energy source [1910.147(d)(4)], to ensure all residual energy had been removed [1910.147(d)(5)(i)], and verification steps [1910.147(d)(6)], were not implemented to protect employees from machine servicing hazards.
Recent events (1)
- — Z (S) $0
More inspections at International Technical Coatings, INC.
View International Technical Coatings, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332618)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343468674.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.