COLUMBUS, OH —
OSHA Inspection: INTERNATIONAL TECHNICAL COATINGS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of INTERNATIONAL TECHNICAL COATINGS, INC. in 845 EAST MARKISON AVE, COLUMBUS, OH 43207 (NAICS 332618). OSHA activity number 344754056.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- INTERNATIONAL TECHNICAL COATINGS, INC.
- Site address
- 845 EAST MARKISON AVE
- City
- COLUMBUS
- State
- OH
- ZIP
- 43207
- Mailing
- 845 EAST MARKISON AVE, COLUMBUS, OH 43207
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332618
- Employees
- 179
- Ownership type
- A
Citations
1 citation on file for this inspection.
1910.147 D
- Issued
- Jul 13, 2020
- Abate by
- Feb 7, 2022
- Penalty
- Initial $106,029 · Current $63,617 Reduced
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence: a. Located at the Ideal FSD 074 Fenceline: On or about May 13, 2020, an employee was exposed to machine hazards associated with moving parts and pinch points while adjusting the grippers on the exit table. The employer relied on machine controls and failed to ensure that hazardous energy control application steps were implemented as the machine was not shut down or turned off to perform the servicing work [per the 1910.147(d)(2) requirements]. As a result, the remaining applicable energy control elements, involving machine isolation [(d)(3)], LOTO device application [(d)(4)], dissipation of stored pneumatic energy [(d)(5)(i)], and verification of isolation [(d)(6)], were not implemented to protect the employee from the machine servicing hazards. b. Located at the Ideal FSD 074 Fenceline: On or about May 13, 2020, an employee was exposed to machine hazards associated with moving parts and pinch points while performing wire alignments when a wire does not feed properly into the welder. The employer relied on machine controls and failed to ensure that hazardous energy control application steps were implemented as the machine was not shut down or turned off to perform the servicing work [per the 1910.147(d)(2) requirements]. As a result, the remaining applicable energy control elements, involving machine isolation [(d)(3)], LOTO device application [(d)(4)], dissipation of stored pneumatic energy [(d)(5)(i)], and verification of isolation [(d)(6)], were not implemented to protect the employee from the machine servicing hazards. International Technical Coatings, Inc. was previously cited for a violation of this Occupational Safety and Health standard, which was contained in OSHA inspection number 1346867, citation number 1, item number 1c and was affirmed as a final order on 02/26/2019, with respect to a workplace located at 845 East Markison Avenue, Columbus, Ohio. International Technical Coatings, Inc. was previously cited for a violation of this Occupational Safety and Health standard, which was contained in OSHA inspection number 1246631, citation number 1, item number 2 and was affirmed as a final order on 09/03/2013, with respect to a workplace located at 845 East Markison Avenue, Columbus,
Recent events (3)
- — J (R) $63617.4
- — C (R) $106029
- — Z (R) $106029
More inspections at International Technical Coatings, INC.
View International Technical Coatings, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332618)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344754056.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.