OSHA Inspection: THE ORLANDO BAKING COMPANY

Issued

Sep 16, 2019

Abate by

Sep 4, 2020

Penalty

Initial $9,472 · Current $9,472

General-duty citation text

29 CFR 1910.212(a)(1): Types of guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks.     On or about May 27, 2019, the employer did not ensure one or more methods of machine guarding was provided to protect employees from the line #8 reciprocating conveyor point of operation while working on or near the reciprocating conveyor to remove pieces of bread dough.

Issued

Sep 16, 2019

Abate by

Sep 4, 2020

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(a)(3)(iii): Special handtools for placing and removing material shall be such as to permit easy handling of material without the operator placing a hand in the danger zone. Such tools shall not be in lieu of other guarding required by this section, but can only be used to supplement protection provided.    On or about May 27, 2019, the employer did not ensure employees hands were not placed in the danger zone (point of operation) of the line #8 reciprocating conveyor when using a hand tool to remove dough from the conveyor.

Issued

Sep 16, 2019

Abate by

Sep 4, 2020

Penalty

Initial $66,300 · Current $13,260 Reduced

General-duty citation text

29 CFR 1910.147(c)(4)(i): Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section.     On or about May 27, 2019, the employer did not ensure an employee utilized the developed and documented procedures for the control of hazardous energy while cleaning the line #8 reciprocating conveyor.          THE ORLANDO BAKING COMPANY, WAS PREVIOUSLY CITED FOR A VIOLATION OF THIS OCCUPATIONAL SAFETY AND HEALTH STANDARD OR ITS EQUIVALENT STANDARD, 29 CFR 1910.147(c)(4)(i), WHICH WAS CONTAINED IN OSHA INSPECTION NUMBER 1265498, CITATION NUMBER 01, ITEM NUMBER 001a AND WAS AFFIRMED AS A FINAL ORDER ON OR ABOUT FEBRUARY 12, 2018 WITH RESPECT TO A WORK PLACE LOCATED AT 7777 GRAND AVENUE, CLEVELAND, OHIO.

Issued

Sep 16, 2019

Abate by

Sep 4, 2020

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence:     On or about May 27, 2019, the employer did not ensure an employee cleaning the line #8 reciprocating conveyor performed and followed the established energy control procedures by; ensured the machine was turned off [per 1910.147(d)(2) requirements], isolated the machine from the energy source(s) [(d)(3)], affixed a lockout device [(d)(4)(i)], and verified de-energization and isolation had been accomplished prior to cleaning the machine [(d)(6)].         THE ORLANDO BAKING COMPANY, WAS PREVIOUSLY CITED FOR A VIOLATION OF THIS OCCUPATIONAL SAFETY AND HEALTH STANDARD OR ITS EQUIVALENT STANDARD, 29 CFR 1910.147(c)(4)(i), WHICH WAS CONTAINED IN OSHA INSPECTION NUMBER 1265498, CITATION NUMBER 01, ITEM NUMBER 001a AND WAS AFFIRMED AS A FINAL ORDER ON OR ABOUT FEBRUARY 12, 2018 WITH RESPECT TO A WORK PLACE LOCATED AT 7777 GRAND AVENUE, CLEVELAND, OHIO.

Issued

Sep 16, 2019

Abate by

Sep 4, 2020

Penalty

Initial $13,260 · Current $0 Reduced

General-duty citation text

29 CFR 1910.147(c)(7)(i)(A): Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control.     On or about May 27, 2019, the employer did not ensure employees required to perform service and maintenance activities, including but not limited too; cleaning the line #8 reciprocating and pan conveyor, were trained and provided with the methods and means necessary for energy isolation and control of the line #8.