HAMMOND, WI —
OSHA Inspection: LOPAREX, LLC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of LOPAREX, LLC in 1740 RIDGEWAY STREET, HAMMOND, WI 54015 (NAICS 322220). OSHA activity number 345663223.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LOPAREX, LLC
- Site address
- 1740 RIDGEWAY STREET
- City
- HAMMOND
- State
- WI
- ZIP
- 54015
- Mailing
- 1740 RIDGEWAY STREET, HAMMOND, WI 54015
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 322220
- Employees
- 168
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 D03
- Issued
- Apr 21, 2022
- Abate by
- Jul 29, 2022
- Penalty
- Initial $13,559 · Current $9,491 Reduced
General-duty citation text
29 CFR 1910.147(d)(3): All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): (a) In the fabrication shop; On or about November 22, 2021, the Bridgeport milling machine, S/N J-114946, was not isolated from the electrical energy source by unplugging the power cord during an end mill bit changing operation.
Recent events (2)
- — I (S) $9491.3
- — Z (S) $13559
1910.147 D04 I
- Issued
- Apr 21, 2022
- Abate by
- Jul 29, 2022
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: (a) In the fabrication shop; On or about November 22, 2021, the Bridgeport milling machine, S/N J-114946, did not have a lockout device affixed to the power cord during an end mill bit changing operation.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- Apr 21, 2022
- Abate by
- Jul 29, 2022
- Penalty
- Initial $7,748 · Current $5,424 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) In the fabrication shop: On or about November 22, 2021, the Bridgeport milling machine, S/N J-114946, did not have a guard for the bit and chuck.
Recent events (2)
- — I (S) $5423.6
- — Z (S) $7748
1910.219 D01
- Issued
- Apr 21, 2022
- Abate by
- May 12, 2022
- Penalty
- Initial $7,748 · Current $5,424 Reduced
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): (a) In the fabrication shop; On or about November 22, 2021, the pulley housing cover for the Bridgeport milling machine, S/N J-114946, had large openings on both the left and right side of the cover, creating exposure to in-going nip points on the pulleys and belt.
Recent events (2)
- — I (O) $5423.6
- — Z (S) $7748
1910.219 E01 I
- Issued
- Apr 21, 2022
- Abate by
- May 12, 2022
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs seven feet or less from the floor level were not guarded with a guard that extended to at least fifteen inches above the belt: (a) In the fabrication shop; On or about November 22, 2021, the pulley housing cover for the Bridgeport milling machine, S/N J-114946, had large openings on both the left and right side of the cover, creating exposure to in-going nip points on the pulleys and belt.
Recent events (2)
- — I (O) $0
- — Z (S) $0
More inspections at Loparex, LLC
View Loparex, LLC's full OSHA safety record →
More inspections in this industry (NAICS 322220)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345663223.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.