ROANOKE, IL —
OSHA Inspection: BELLA ELEVATOR, LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of BELLA ELEVATOR, LLC in 509 W FRONT ST, ROANOKE, IL 61561 (NAICS 333921). OSHA activity number 346748528.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BELLA ELEVATOR, LLC
- Site address
- 509 W FRONT ST
- City
- ROANOKE
- State
- IL
- ZIP
- 61561
- Mailing
- 10000 N GALENA RD., PEORIA, IL 61615
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333921
- Employees
- 95
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.22 A01
- Issued
- Nov 14, 2023
- Abate by
- Nov 27, 2023
- Penalty
- Initial $8,036 · Current $4,000 Reduced
General-duty citation text
29 CFR 1910.22(a)(1): The employer did not ensure that all places of employment, passageways, storerooms, service rooms, and walking-working surfaces are kept in a clean, orderly, and sanitary condition: On or about June 5, 2023, employees were exposed to fire and tripping hazards when working in the Cab Shop and the employer had not ensured walking-working surface accumulations of wood dust were not allowed to accumulate on the floor.
Recent events (2)
- — I (S) $4000
- — Z (S) $8036
1910.23 B13
- Issued
- Nov 14, 2023
- Abate by
- Dec 14, 2023
- Penalty
- Initial $8,036 · Current $0 Reduced
General-duty citation text
29 CFR 1910.23(b)(13): The employer did not ensure that no employee carries any object or load that could cause the employee to lose balance and fall while climbing up or down the ladder: On or about June 5, 2023, employees were exposed to fall hazards up to four feet when climbing a Little Giant Safety Step Model 10410BA while carrying elevator cab roofs and the employer had not ensured employees did not carry loads that could affect balance while climbing a portable ladder.
Recent events (2)
- — I (O) $0
- — Z (S) $8036
1910.212 A01
- Issued
- Nov 14, 2023
- Abate by
- Nov 27, 2023
- Penalty
- Initial $8,036 · Current $4,000 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: On or about June 5, 2023, employees were exposed to contact with rotating drill bits while operating drill presses and the employer had not ensured machine guards were installed.
Recent events (2)
- — I (S) $4000
- — Z (S) $8036
1910.213 C01
- Issued
- Nov 14, 2023
- Abate by
- Nov 27, 2023
- Penalty
- Initial $8,036 · Current $4,000 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: On or about June 5, 2023, an employee was exposed to struck by hazards and contact with rotating saw blade when rip sawing dimensional hardwood on the SawStop table saw located on the North end of the Cab Shop and the employer had not ensured the blade guard was installed.
Recent events (2)
- — I (S) $4000
- — Z (S) $8036
1910.213 C03
- Issued
- Nov 14, 2023
- Abate by
- Nov 27, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: On or about June 5, 2023, an employee was exposed to struck by hazards when rip sawing dimensional hardwood on the SawStop table saw located on the north end of the Cab Shop and the employer had not ensured non kickback fingers were installed.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 D01
- Issued
- Nov 14, 2023
- Abate by
- Nov 27, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(d)(1): Circular handfed crosscut table saw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: On or about June 5, 2023, employees were exposed to contact with rotating saw blade when cross cutting dimensional hardwood and sawing Medium Density Fiberboard (MDF) on the SawStop table saws located in the Cab Shop and the employer had not ensured the blade guards were installed.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Bella Elevator, LLC
View Bella Elevator, LLC's full OSHA safety record →
More inspections in this industry (NAICS 333921)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346748528.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.