GAP, PA —
OSHA Inspection: PINE HILL MANUFACTURING, LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of PINE HILL MANUFACTURING, LLC in 5140 MARTIN DRIVE, GAP, PA 17527 (NAICS 336214). OSHA activity number 347399834.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PINE HILL MANUFACTURING, LLC
- Site address
- 5140 MARTIN DRIVE
- City
- GAP
- State
- PA
- ZIP
- 17527
- Mailing
- 5140 MARTIN DRIVE ATTN: DARRELL BISHOP, GAP, PA 17527
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336214
- Employees
- 69
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.184 D
- Issued
- Jul 25, 2024
- Abate by
- Aug 13, 2024
- Penalty
- Initial $8,296 · Current $4,148 Reduced
General-duty citation text
29 CFR 1910.184(d): Sling(s) and fastenings were not inspected each day or during use and were not removed from service when damaged or defective: (a) 5140 Martin Drive, Gap, PA; Small Parts Welding Station, 5-ton hoist - On or about April 9, 2024, the employee was using the metal chain sling hook to lift metal parts for welding weighing approximately 200lbs without a safety latch across the hook throat. The employee was exposed to a crushing hazard. (b) 5140 Martin Drive, Gap, PA; Single Frame Truck Weld Station, 10-ton hoist - On or about April 9, 2024, the metal chain sling hook which was used to lift and move trailers being assembled did not have a safety latch across the hook throat. Employees were exposed to a crushing hazard. Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
- — I (S) $4148
- — Z (S) $8296
1910.243 C01
- Issued
- Jul 25, 2024
- Abate by
- Aug 13, 2024
- Penalty
- Initial $12,445 · Current $6,223 Reduced
General-duty citation text
29 CFR 1910.243(c)(1): Abrasive wheel(s) were used on portable grinder(s) which were not provided with safety guard(s) meeting the requirements specified in 29 CFR 1910.243(c)(1) through (c)(4): (a) 5140 Martin Drive, Gap, PA; small parts welding workstation - On or about April 9, 2024, an employee was using the Top Cat pneumatic grinder (s/n 105364) which did not have a guard installed. The employee was exposed struck-by hazards. (b) 5140 Martin Drive, Gap, PA; fabrication station - On or about April 9, 2024, an employee was using the Ingersoll Rand pneumatic disk grinder which did not have a guard installed. The employee was exposed struck-by hazards. (c) 5140 Martin Drive, Gap, PA; trailer welding station - On or about April 9, 2024, the snap-on pneumatic angle grinder and the snap-on pneumatic cut off wheel did not have the guard installed. Employee(s) were exposed struck-by hazards. Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
- — I (S) $6222.5
- — Z (S) $12445
1910.145 C03
- Issued
- Jul 25, 2024
- Abate by
- Aug 13, 2024
- Penalty
- Initial $1,165 · Current $583 Reduced
General-duty citation text
29 CFR 1910.145(c)(3):Safety instruction sign(s) were not used where there was a need for general instructions and suggestions relative to safety measure(s): (a) 5140 Martin Drive, Gap, PA; initial fabrication storage rack - On or about April 9, 2024, the racking system used to store the bulk metal stock used for fabrication was not labeled with load limit. Employees were exposed to crushing hazards. Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
- — I (O) $582.5
- — Z (O) $1165
More inspections at Pine Hill Manufacturing, LLC
View Pine Hill Manufacturing, LLC's full OSHA safety record →
More inspections in this industry (NAICS 336214)
More inspections in PA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347399834.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.