LONDON, OH —
OSHA Inspection: STANLEY ELECTRIC U.S. CO., INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of STANLEY ELECTRIC U.S. CO., INC. in 480 E HIGH ST, LONDON, OH 43140 (NAICS 336320). OSHA activity number 348599473.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- STANLEY ELECTRIC U.S. CO., INC.
- Site address
- 480 E HIGH ST
- City
- LONDON
- State
- OH
- ZIP
- 43140
- Mailing
- 420 EAST HIGH STREET, LONDON, OH 43140
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336320
- Employees
- 985
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C04 I
- Issued
- Jan 23, 2026
- Abate by
- Feb 12, 2026
- Penalty
- Initial $9,457 · Current $6,620 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section. a. On or about November 18, 2025, at the assembly area finishing line of the facility, the employer did not ensure employees utilized the energy control procedures when they performed maintenance on the machines such as, but not limited to the Solder Robot Machine, SMMS-14575. The condition exposed employees were exposed to caught-in hazards as a result.
Recent events (2)
- — I (S) $6619.9
- — Z (S) $9457
1910.147 D
- Issued
- Jan 23, 2026
- Abate by
- Feb 12, 2026
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedure) was not done in sequence as required by 29 CFR 1910.147(d)(1) through (d)(6): a. On or about November 18, 2025, at the finishing area location at the assembly line of the facility employees were exposed caught-in and struck-by hazards when they performed maintenance and servicing on the machines such as, but not limited to the Solder Robot Machine, SMMS-14575, finishing line. The employer did not ensure that the authorized employee was knowledgeable on the type and magnitude of the energy to be controlled, the hazards of the energy to be controlled and the means to control the energy prior to performing the maintenance work [per the 1910.147(d)(1) requirements]. The employer failed to ensure that the energy control application steps were implemented as the machine was not shut down or turned off to perform the servicing work [per the 1910.147 (d)(2) requirements]. As a result, the remaining applicable energy control elements, involving machine isolation [(d)(3)], LOTO device application [(d)(4)], dissipation of residual energy [(d)(5)], and verification of isolation [(d)(6)], were not implemented to protect the employees from the Solder Robot Machine, SMMS-14575, finishing line servicing hazards. The condition exposed employees were exposed to caught-in hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C06 I
- Issued
- Jan 23, 2026
- Abate by
- Feb 12, 2026
- Penalty
- Initial $9,457 · Current $6,620 Reduced
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer shall conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirements of this standard are being followed. a. On or about November 18, 2025, the employer did not ensure that periodic inspections were conducted for the authorized employees at the assembly area finishing line of the facility, who were tasked with performing maintenance and servicing on machines such as, but not limited to, the Solder Robot Machine, SMMS-14575. As a result, employees were exposed to caught-in hazards.
Recent events (2)
- — I (S) $6619.9
- — Z (S) $9457
1910.147 C07 I A
- Issued
- Jan 23, 2026
- Abate by
- Feb 12, 2026
- Penalty
- Initial $9,457 · Current $6,620 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control. a. On or about November 18, 2025, at the assembly area finishing line of the facility, the employer did not ensure that authorized employees were adequately trained to recognize the methods and means necessary for energy isolation and control when performing service or maintenance on equipment, including but not limited to the Solder Robot Machine, SMMS-14575. As a result, employees were exposed to caught-in hazards.
Recent events (2)
- — I (S) $6619.9
- — Z (S) $9457
More inspections at Stanley Electric U.S. CO., INC.
View Stanley Electric U.S. CO., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 336320)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348599473.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.