DENVER, CO —
OSHA Inspection: MONARCH METAL MANUFACTURING, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of MONARCH METAL MANUFACTURING, INC. in 2597 W. 64TH AVE., UNIT 1, DENVER, CO 80221 (NAICS 332322). OSHA activity number 313416778.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MONARCH METAL MANUFACTURING, INC.
- Site address
- 2597 W. 64TH AVE., UNIT 1
- City
- DENVER
- State
- CO
- ZIP
- 80221
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332322
- SIC code (legacy)
- 3444
- Employees
- 22
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $750 · Current $593 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that the employer did not maintain a safe distance from the point of operation on the Amada Power Press Brakes exposing employees to an amputation hazard: (a)Monarch Metal Manufacturing, Inc. & 2597 W. 64th Ave., Denver, CO 80221: On and before February 19th, 2010, the employer did not ensure that a safety program which included safe work procedures, training, and supervision to ensure that operating power press brakes safely by maintaining a safe distance from the point of operation. Note: Safeguarding by maintaining a "safe distance is acceptable, during normal production operation, if the operating employee does not approach closer than necessary and in no case, closer than 4 inches (10.16 centimeters), to the power press brake point of operation as required under CPL 2-1.25, Guidelines for Point of Operation Guarding of Power Press Brakes paragraph and ANSI B11.3-1982, Safety Requirements for Power Press Brakes. This condition exposed the employees to an amputation hazard. Among others, one feasible and acceptable abatement method to correct this hazard is to ensure that each employee who works on the power press brakes receives training, and supervision to ensure that operating power press brakes safely by maintaining a safe distance from the point of operation. Safeguarding by maintaining a "safe distance is acceptable, during normal production operation, if the operating employee does not approach closer than necessary and in no case, closer than 4 inches (10.16 centimeters), to the power press brake point of operation as required under CPL 2- 1.25, Guidelines for Point of Operation Guarding of Power Press Brakes paragraph and ANSI B11.3-1982, Safety Requirements for Power Press Brakes. Abatement Note: Abatement certification and documentation are required for this item (see enclosed "Sample Abatement Certification Letter").
Recent events (2)
- — I (S) $593.00
- — Z (S) $750.00
1910.22 D01
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $225 · Current $179 Reduced
Recent events (2)
- — I (S) $179.00
- — Z (S) $225.00
1910.38 A01
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $300 · Current $238 Reduced
Recent events (2)
- — I (S) $238.00
- — Z (S) $300.00
1910.147 C01
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $300 · Current $238 Reduced
Recent events (2)
- — I (S) $238.00
- — Z (S) $300.00
1910.178 Q07
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $225 · Current $179 Reduced
Recent events (2)
- — I (O) $179.00
- — Z (S) $225.00
1910.305 G01 IIIA
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $300
Recent events (2)
- — I (S)
- — Z (S) $300.00
1910.305 G01 IVB
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
Recent events (2)
- — I (S)
- — Z (S)
1910.242 B
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $225 · Current $179 Reduced
Recent events (2)
- — I (S) $179.00
- — Z (S) $225.00
1910.1200 H01
- Issued
- Jun 18, 2010
- Abate by
- Jul 14, 2010
- Penalty
- Initial $225 · Current $179 Reduced
Recent events (2)
- — I (S) $179.00
- — Z (S) $225.00
More inspections at Monarch Metal Manufacturing, INC.
View Monarch Metal Manufacturing, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332322)
More inspections in CO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 313416778.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.