CUMMING, GA —
OSHA Inspection: SUNSET CONTRACTORS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SUNSET CONTRACTORS, INC. in 7006 COLFAX RD, CUMMING, GA 30040 (NAICS 238130). OSHA activity number 337168983.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SUNSET CONTRACTORS, INC.
- Site address
- 7006 COLFAX RD
- City
- CUMMING
- State
- GA
- ZIP
- 30040
- Mailing
- 3635 BRADFORD WALK TRL., BUFORD, GA 30519
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 3
- Ownership type
- A
Citations
3 citations on file for this inspection.
1926.403 B01
- Issued
- Jan 9, 2013
- Abate by
- Feb 5, 2013
- Penalty
- Initial $1,200 · Current $1,200
General-duty citation text
29 CFR 1926.403(b)(1): Employer did not ensure that electrical equipment is free from recognized hazards that are likely to cause death or serious physical harm to employees. On or about November 1, 2012: (a) Employee engaged in nailing operations using a pneumatic nail gun was exposed to electrical shock and burns when the plug powering a Dewalt air compressor was damaged.
Recent events (1)
- — Z (S) $1200
1926.404 F06
- Issued
- Jan 9, 2013
- Abate by
- Feb 5, 2013
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.404(f)(6): The path to ground from circuits, equipment, or enclosures was not permanent and continuous. On or about November 1, 2012; (a) Employee engaged in cutting operations was exposed to electrical shock and or burns while using a Makita circular saw that was being powered by a flexible cord that had a grounding pin missing.
Recent events (1)
- — Z (S) $0
1926.501 B13
- Issued
- Jan 9, 2013
- Abate by
- Feb 5, 2013
- Penalty
- Initial $2,800 · Current $2,800
General-duty citation text
29 CFR 1926.501(b)(13): Each employee engaged in residential construction activities 6 feet (1.8 m) or more above lower levels was not protected by guardrail systems, safety net systems, personal fall arrest systems, or an alternative fall protection measure under another provision of paragraph 1926.501 (b), nor did the employer demonstrate that it is infeasible or creates a greater hazard to use these systems and develop and implement a fall protection plan which meets the requirements of paragraph (k) of section 1926.502: On or about November 1, 2012: (a) Employee engaged in the installation of flashing around a second story window, was exposed to fall hazards of approximately 16 feet while standing on window sill without the use of fall protection systems.
Recent events (1)
- — Z (S) $2800
More inspections at Sunset Contractors, INC.
View Sunset Contractors, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 337168983.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.