WOLFFORTH, TX —
OSHA Inspection: SCOTT MANUFACTURING, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of SCOTT MANUFACTURING, INC. in 10609 FM 1585, WOLFFORTH, TX 79382 (NAICS 332313). OSHA activity number 347171860.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SCOTT MANUFACTURING, INC.
- Site address
- 10609 FM 1585
- City
- WOLFFORTH
- State
- TX
- ZIP
- 79382
- Mailing
- P.O. BOX 102408, LUBBOCK, TX 79408
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332313
- Employees
- 54
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.28 B01 I
- Issued
- May 10, 2024
- Abate by
- Jun 10, 2024
- Penalty
- Initial $12,421 · Current $7,453 Reduced
General-duty citation text
29 CFR 1910.28(b)(1)(i):29 CFR 1910.28(b)(1)(i): Except as provided elsewhere in this section 29 CFR 1910.28, the employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the systems described in 29 CFR 1910.28(b)(1)(i): On or about December 12, 2023 and times prior to, employee(s) working from an elevated platform with unprotected side and edges at a heights greater than four feet above the lower level were exposed to fall hazards.
Recent events (2)
- — I (S) $7452.6
- — Z (S) $12421
1910.132 H01
- Issued
- May 10, 2024
- Abate by
- Jun 10, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.132(h)(1):Except as provided by paragraphs (h)(2) through (h)(6) of this section, the protective equipment, including personal protective equipment (PPE), used to comply with this part, shall be provided by the employer at no cost to employees. On or about December 12, 2023, employer failed to provide employees working at heights greater than 4 feet with fall protection equipment exposing employees to fall hazards while working from an unguarded elevated platform.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.178 A05
- Issued
- May 10, 2024
- Abate by
- Jun 10, 2024
- Penalty
- Initial $8,873 · Current $5,324 Reduced
General-duty citation text
29 CFR 1910.178(a)(5):The powered industrial truck was equipped with front-end attachments other than factory installed attachments, however the employer did not request that the truck be marked to identify the attachments and show the approximate weight of the truck and attachment combination at maximum elevation with load laterally centered: On or about December 12, 2023 or times prior to, the employer did not update the Doosan Fork lift Serial # FDA2C-5052-01297 capacity data plate to reflect the addition of a shop fabricated work platform, forklift attachments, exposing employees to roll over hazards.
Recent events (2)
- — I (S) $5323.8
- — Z (S) $8873
1910.178 L06
- Issued
- May 10, 2024
- Abate by
- Jun 10, 2024
- Penalty
- Initial $5,323 · Current $3,194 Reduced
General-duty citation text
29 CFR 1910.178(l)(6): Certification. The employer shall certify that each operator has been trained and evaluated as required by this paragraph (l). The certification shall include the name of the operator, the date of the training, the date of the evaluation, and the identity of the person(s) performing the training or evaluation. On or about December 12, 2023 or times prior to the employer did not certify employee(s) operating forklifts had successfully completed required training, exposing employees to roll over and struck-by hazards.
Recent events (2)
- — I (S) $3193.8
- — Z (S) $5323
1910.30 A01
- Issued
- May 10, 2024
- Abate by
- Jun 10, 2024
- Penalty
- Initial $996 · Current $598 Reduced
General-duty citation text
29 CFR 1910.30(a)(1): The employer did not provide training for each employee who uses personal fall protection systems or who is required to be trained as specified elsewhere in this subpart before any employee is exposed to a fall hazard. And/or the employer did not ensure employees are trained in the requirements of this paragraph on or before May 17, 2017. On or about December 12, 2023 or times prior to, employee(s) were exposed to fall hazards when employer did not ensure employees are trained in the use of fall protection from elevated platform.
Recent events (2)
- — I (O) $597.6
- — Z (O) $996
More inspections at Scott Manufacturing, INC.
View Scott Manufacturing, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332313)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347171860.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.